整机装配图
多功能果蔬去皮加工机设计
摘要
主要介绍了以磨削原理为基础的，适合食品加工厂等场所使用的水果去皮机的设计要点，水果去皮机主要由动力部分，传动部分，料仓和机架等部分组成。电机轴上带轮通过V型带向大带轮传递动力，大带轮再通过键向与之紧密联结的主轴输送动力，带动工作圆盘转动，水果被不断挤压，与筒壁内摩擦片碰撞，表皮被磨削掉，然后冲洗，准备下一工序。通过对原始数据的分析，方案的论证比较，和有关数据的分析计算，完成了水果去皮机的总体方案设计。
关键词：水果去皮带传动电主轴磨削
Abstract
This paper mainly introduces the design points of the fruit peeling machine, which is based on the grinding principle and is suitable for the food processing plant and other places. The fruit peeling machine is mainly composed of the power part, the transmission part, the silo and the rack. The pulley on the motor shaft passes through the V belt to the large belt wheel. The large belt pulley conveys the power to the spindle which is closely connected to the spindle, drives the working disk to rotate. The fruit is continuously extruded and collided with the friction plate inside the wall. The skin is grinded off, then flushed and prepared for the next process. Through the analysis of the original data, the comparison of the scheme, and the analysis and calculation of the relevant data, the overall design of the fruit peeling machine is completed.
Key words: fruit peeling; belt drive; motorized spindle; grinding
目录
摘要1
Abstract 2
1引言4
1.1果蔬原料加工预处理4
1.2原料的清洗4
2果蔬加工方法4
3结构部分5
3.1基本结构5
3.1.2工作转盘6
3.1.3齿轮传动方案7
3.1.4其他8
3.2工作原理8
4果蔬原料去皮机的参数确定8
4.1物料在工作圆筒内的受力分析9
4.2工作转盘转速的确定10
4.3去皮机功率的确定11
4.4选择电动机12
4.5整机主要参数指标（JB/T 10391-2008） 14
5主要零件的结构设计与计算15
5. 1 V带轮结构设计计算15
5.2传动主轴的结构设计计算17
5. 3轴上零件的周向定位19
5. 4确定轴上圆角和倒角尺寸19
5. 5滚动轴承的初步选择19
5. 6轴承盒盖的设计20
6.主要零件的校核20
6.1滚动轴承的寿命计算20
6.1.1作出轴的计算简图21
6.1.2轴的强度校核计算22
6.1.3按弯扭合成应力校核轴的强度22
6.2键的选择及其校核23
6.2.1电动机轴上键的选择23
6.2.2大带轮轴键的选择24
6.3电气PLC控制图24
结论26
参考文献28
A0整机装配图副本
传动主轴
大带轮
机架
小带轮
轴承端盖
设计摘要部分
设计字数统计
设计所包含文件
设计目录
