工件图
带小圆孔U形筒形件-油箱盖的冲压模具设计【拉伸-冲孔复合模】
摘要:本模具设计题目为油箱盖的落料,拉深,冲孔复合模,此零件需三道工序完成.体现了复杂零件的设计要求,内容及方向.具有一定的设计意义,通过对该零件模具的设计进一步加强了设计者冲压模具设计的基础知识,为设计更复杂的冲压模做好了铺垫和吸取了更深该的经验.
本设计运用冲压模具设计与制造工艺基础知识,首先分析了端盖零件的外形,尺寸,精度要求,进行了工艺分析,考虑到此零件为圆形零件,对同轴度要求较高,因此采用复合模工艺方案.然后根据零件的外形尺寸计算毛坯总体尺寸,设计排样图及计算材料利用率及压力中心最后计算出工作部分尺寸,模具总体尺寸,总体尺寸包括工作零部件的结构设计,卸料装置的设计以及固定零件的设计与运用.
本模具的特点是推板在弹顶器,顶杆的作用下,处于最上位置,定位板固定坯料,上模部分下降,利用凸凹模和成形推板进行弯曲,上模继续下降,推动成形推板下降,此时由落料凹模,在成形推板内装有6根顶杆,开模时可使工件抬起,便于取件.
关键词:拉深模复合模凸凹模
The Piercing Die Design Of Tank Cover
Abstract: This mold design topic for the straining die, falls the material, the punch holes superposable die, this components need threeworking procedures to complete. Has manifested the complex components design request, the content and the direction. Has certain design significance, through further strengthened the elementary knowledge to this components mold designwhich the designer ramming mold designs, for designed more complex flushes the die to complete the upholstery and to absorb a deeper this experience.
This design utilization ramming mold design and the manufacture craft elementary knowledge, has first analyzed the end cover components contour, the size, the precision request, has carried on the craft analysis, considered this components are the circular components, is high to the proper alignment request, therefore uses the superposable die craft plan. Then the basis components external dimensions computation semifinished materials overall size, a design row of specimen map and the computation material use factor and the center of pressure last count is present atwork makes the partial sizes, the mold overall size, the overall size including thework spare part structural design, the dumping device design aswell as the fixed components design and the utilization.
This mold characteristic is the small end cover drawing, falls the material, the punch holes superposable die.
The formed push pedal goes against in the ball, under the roof bar function, is in on most the position, the nursery lives the semifinished materials, the top die part drops, the use convex-concave mold and the formed push pedal carry on the drawing and press the shape, the top die continue to drop, impel the formed push pedal to drop, this time by falls the material concave mold, the convex-concave mold carries on falls the material, then flushes the bottom hole. When formed push pedal and dead plate contact, then carries on the reshaping. Is loadedwith 6 roof bars in the formed push pedal, operateswhen the mold may cause thework piece to lift, is advantageous for takes.
Keywords: The straining die compound die Falls the material convex-concave mold
目录
1绪论…………………………………………………………………………………1
1.1冲压的概念、特点及应用……………………………………………………1
1.2冲压的基本工序及冲压的基本类型…………………………………………2
1.3冲压技术的现状及发展方向………………………………………………2
2油箱盖冲压工艺的分析………………………………………………………………4
2.1油箱盖工艺分析……………………………………………………………4
2.2确定工艺方案和工艺计算……………………………………………………4
2.2.1冲材工艺方案的确定…………………………………………………… 4
2.2.2毛坯尺寸算…………………………………………………………… 5
2.2.3确定是否用压圈……………………………………………………… 5
2.2.4排样及相关计算……………………………………………………… 5
2.3设计冲压与压力中心,初选压力机………………………………………… 7
2.3.1冲裁力……………………………………………………………………7
2.3.2压力中心…………………………………………………………………8
2.3.3计算凸凹模刃口尺寸及公差……………………………………………8
3模具的总体设计……………………………………………………………………10
3.1模具类型的选择…………………………………………………………10
3.1模具类型的选择………………………………………………………… 10
3.3卸料出件方式的选择………………………………………………………10
3.4导向方式的选择……………………………………………………………10
4模具工作零件的设计…………………………………………………11
4.1主要零件的结构设计………………………………………………………11
4.1.落料凹模…………………………………………………………………11
4.1.2冲孔凸模………………………………………………………………11
4.2其它零件的结构设计与选用………………………………………………13
4.2.1弹性元件的设计……………………………………………………… 13
4.2.2导向元件的设计……………………………………………………… 13
4.2.3模柄…………………………………………………………………… 13
4.2.4紧固零件及定位零件的设计…………………………………………14
4.2.5卸料与出件零件的设计………………………………………………15
4.2.6选用模架、确定闭合高度及总体尺寸…………………………………15
5模具总装图…………………………………………………………………………17
6模具零件加工工艺………………………………………………………………18
结束语…………………………………………………………………………………21
致谢……………………………………………………………………………………22
参考文献………………………………………………………………………………23
拉深冲孔复合模装配图
凹模
过程卡
零件分析
模柄
排样图
上模座
设计目录
设计摘要
设计字数统计
凸凹模
凸凹模2
凸模
下模座
卸料螺钉
